Chapter 105: So which one? (1/2)

Chapter 105: So which one?

Translated by me, edited by drpetro

Under Ki eyes, the

Don’t look down on that hammer, as it was also of uncommon quality

After several hits, theon, then took out a metal probe, and poked at the crack on top of the power shaft

Then the lass bottles, each filled with different colours of powder

This was powdered metal, steel powder, chromium powder, powdered silica, and nickel powder Last tie ht back a bunch of metal powders These redients used inout those powders, naturally y to repair the shaft

It was just that the chief and all the sailors present, were all professionals of the trade, especially the chief, who had soin with

He felt like this was completely bullshi+t Only with a couple of pokes fro to mix powders There wasn’t even any questions on what materials the shaft was made out of, nor were any steps taken to exa thethe metal powders, the chief and all the other sailors nearly fainted

This guy……

Actually only used a spoon He didn’t even bothering to prepare a must have scale

Any kind of alloy must have their different metal proportions be accurate to two deci medicine, the more precise the proportions were, thea spoon to measure, from those sailors’ point of vieasn’t different frorab at all

They all burst out laughing at thethe powders, but it all came to an abrupt end

If you wanted to have the powder fuse with the shaft after the , then the two metals needed to be of the same proportions When the proportions were the same, then the colours of the two lass vessel, the final mixed metal product, no le difference in colour froure out the proportions was a very unscientific and unconvincing move

However, the old ht, it was as if he had done it thousands of ti spoon, mixed out the exact proportions of the shaft metal; not 1 more or 1 less

That was a move that was both extree of the industry

Thepowder y to fix flaws required the powder to be blasted on, then using high heat to melt it so that it binds onto the base

The master artisan didn’t blast on the metal powder Rather, he slowly operated the solid state laser welder’s welding arm to over the crack, then aim at the crack on the power shaft with its diae protectors dropped down, to signal its operational status, Ye Qing put on his pair of cool sunglasses

Right now, Kim Hunhil and the other sailors had already been shocked into ht was of ordinary quality, used real actions to separate itself from the norm

As the ht coh there was a layer of protectors in place, it still covered the rooe

What kind of terrifying laser poas this?

Finding the orange light in the roo, several people turned their eyes for a look

A beaht that was as thick as a pen e protectors with extremely quick speeds

Zizi Zizi

Sounds of h temperature beam sounded off in everyone’s ears

Two , and the protectors were lifted

Everyone could see that the originally deep crack on the power shaft had already been turned into a very rectangular shaped hole, which has been filled with piping hot liquid like metals

Several seconds later, the residual heat froinal colours

Apart fro, everyone else was completely dumbstruck

Because they found that this crack had not only beco teenerated by the laser had melted the metal powder into liquid, which slowly seeped into the botto in this crack, it also conveniently ular shape

It was also this which left Kih to to fit in 10 whole eggs They had all handled laser welders before, so they were all fa point, then when they cooled off, naturally they were fused together

Except it was just that this heating was limited, and also very uncontrollable

The laser welder in front of thee Kier he stayed shocked, the more face he’d lose

Except he couldn’t control his body at all Going from ridicule, to doubt, and finally to shock Ki led away by the snout by the master artisan and the laser welder

All of their expression changes were seen in full by Ye Qing

To be fair, the more one knew, the more shock and disbelief they would feel of the master artisan and the tools from the Monster Factory

The master artisan, not too slow, and not too fast, poured the rest of the already mixed metal powder into the pool of liquid inally nearly 6 centile centi powdered h temperature laser to turn the metal powder into a thin layer of ain and again

15 minutes later, the last layer of powder metal was fused with the power shaft